If no type tests are requested within the type-examination procedure (see point 4.4), and the type is sufficiently defined by the technical documentation, as described in point 3, the notified body may agree, that no specimens are placed at their disposal.

The manufacturer must take all measures necessary in order that the manufacturing process ensures conformity of the interoperability constituents with the type as described in the EC type-examination certificate and with the requirements of Directive 96/48/EC and of the TSI that apply to them.

Type-examination certificates issued and measurements of equipment carried out under the Directives mentioned in paragraph 1 may be used in drawing up the technical documentation provided for in Annex V point 3, Annex VI point 3, Annex VII point 2, Annex VIII points 3.1 and 3.3 of this Directive.

Within that part of the procedure the adjudicating entity or his authorised representative established within the Community checks and attests that the subsystem concerned is in conformity with the type as described in the EC type-examination certificate and satisfies the requirements of Directive 96/48/EC and of the TSI that apply to them.

These batches shall be accompanied by the EC type-examination certificate referred to in Article 10, or, where the vessels are not manufactured in accordance with an approved prototype, by the design and manufacturing schedule referred to in Annex II section 3. In this case the approved body shall, prior to EC verification, examine the schedule in order to certify its conformity.

IN ADDITION TO THE TESTING STANDARDS SPECIFICALLY MENTIONED, A NUMBER OF PROVISIONS, WHICH MUST BE CHECKED DURING TYPE-EXAMINATION (TYPE APPROVAL) AS REFERRED TO IN THE MODULES FOR CONFORMITY ASSESSMENT IN ANNEX B, ARE TO BE FOUND IN THE APPLICABLE REQUIREMENTS OF THE INTERNATIONAL CONVENTIONS AND THE RELEVANT RESOLUTIONS AND CIRCULARS OF THE IMO

The notified body must carry out the appropriate examinations and tests in order to check the conformity of the subsystem with the type as described in the EC type-examination certificate and with the requirements of the TSI by examination and testing of every subsystem, manufactured as a serial product, as specified under point 4.

This module describes the EC verification procedure whereby a notified body checks and certifies, at the request of an adjudicating entity or its authorised representative established within the Community, that a rolling stock subsystem, for which an EC type-examination certificate has already been issued by a notified body,

This module describes the EC verification procedure whereby a notified body checks and certifies at the request of an adjudicating entity or its authorised representative established within the Community, that a rolling stock subsystem, for which an EC type-examination certificate has already been issued by a notified body,

Every product is examined individually and the appropriate tests defined in the relevant standard(s) referred to in Article 5 or equivalent tests must be carried out in order to verify the conformity of the products with the EC type described in the type-examination certificate and with the requirements of the Directive which apply to them.

Whereas certification procedures must be established to define the way in which national approved bodies have to approve models of toys not in conformity with standards and issue type-examination certificates for them and for toys in conformity with standards, a model of which is submitted to them for approval;

EC verification is the procedure whereby the manufacturer or his authorized representative established within the Community ensures and declares that the instruments which have been checked in accordance with paragraph 3.3 are, where applicable, in conformity to the type described in the EC type-examination certificate and satisfy the requirements of the Directive which apply to them. 3.2.

The applicant must inform the notified body that holds the technical documentation concerning the EC type-examination certificate of all modifications to the approved subsystem which must receive additional approval where such changes may affect the conformity with the requirements of Directive 96/48/EC and of the TSI or the prescribed conditions for use of the subsystem.

All subsystems (as serial products) must be individually examined and appropriate tests and verifications as set out in the TSI and in the relevant European specifications (or equivalent tests) shall be carried out in order to verify their conformity with the type as described in the type-examination certificate and the requirements of the TSI that apply to them.

All products must be individually examined and appropriate tests as set out in the relevant European specifications referred to in Article 10 or equivalent tests shall be carried out in order to verify their conformity with the type as described in the EC type-examination certificate and the requirements of Directive 96/48/EC and of the TSI that apply to them.

Member States shall presume that toys in respect of which the manufacturer has not applied the standards referred to in paragraph 1, or has applied them only in part, or for which no such standards exist, satisfy the essential requirements referred to in Article 3 where, after receipt of an EEC type-examination certificate, their conformity with the approved model has been certified by the affixation of the EC mark.

The products which make up the sample are examined and the appropriate tests defined in the relevant standard(s) referred to in Article 5 or equivalent tests must be carried out to verify, where appropriate, the conformity of the products with the type described in the EC type-examination certificate and with the requirements of the Directive which apply to them in order to determine whether to accept or reject the batch.

This module describes that part of the procedure whereby a manufacturer or his authorised representative established within the Community checks and attests that the interoperability constituent concerned, subject to the provisions of point 3 is in conformity with the type as described in the EC type-examination certificate and satisfies the requirements of Directive 96/48/EC and of the TSI that apply to it.

a description of the means (such as the use of a test report or technical file) whereby the manufacturer ensures conformity of production with the standards referred to in Article 5 (1) and, as appropriate: an EC type-certificate drawn up by an approved body; copies of the documents the manufacturer has submitted to the approved body; a description of the means whereby the manufacturer ensures conformity with the approved model,

The notified body must carry out the appropriate examinations and tests in order to check the conformity of the interoperability constituent with the type as described in the EC type-examination certificate and with the requirements of Directive 96/48/EC and of the TSI either by examination and testing of every interoperability constituent as specified in point 4 or by examination and testing of interoperability constituents on a statistical basis, as specified in point 5, at the choice of the manufacturer.